 |
Options
| Step 4 -
Memory - Mandatory |
Memory Configuration
Guidelines
Memory options should be selected in the context of the applications sensitivity to
memory bandwidth and future memory capacity expansion. This will determine the number of
memory options to order. The total capacity required will determine the size of the
options to be ordered.
- Mandatory
selection of at least one memory option required per ES47 tower system.
- Each ES47 tower system supports up to four memory options (four RIMMs each) and up to
four memory RAID options (one RIMM each) for a total of 20 RIMMs.
- Each CPU has two memory controllers.
- Each memory controller can support four RIMMs (one memory option) and a fifth RIMM slot
for redundancy (RAID option).
- If populated, the two memory controllers per CPU must contain the same size
RIMMs.
- Order one RAID option (one RIMM) per memory option if desired.
- If RAID memory option is selected, the number of RAID options selected must equal
the number of memory options selected.
The following examples illustrate different ways of configuring an ES47 Tower system
with a total of 2 GB of memory |
| |
| |
|
ES47
Tower System |
Case |
Memory Option |
CPU
1 |
CPU
2 |
| Controller 1 |
Controller 2 |
Controller 1 |
Controller 2 |
| A |
3X-MS7AB-AA (4x128MB) |
1 |
1 |
1 |
1 |
| B |
3X-MS7AB-BA (4x256MB) |
1 |
- |
1 |
- |
| C |
3X-MS7AB-CA (4x512MB) |
1 |
- |
- |
- |
| |
| Memory Application Examples |
Configuring memory is a compromise between
cost, total memory capacity, and memory bandwidth requirements. The behavior of the
application must be used to define the most-desired configuration. Some applications are
sensitive to memory capacity while some are sensitive to memory bandwidth. If actual
application measurements are not available, the following may be used as guidelines:
- Large memory (VLM) applications, in which large amounts of memory can substantially
reduce I/O throughput, may be optimized for total memory capacity and future capacity
growth. In VLM applications, the right balance might be one memory option per CPU. (Case
B)
- Typical commercial applications, such as transaction processing (OLTP) and multi-user
timesharing, usually operate efficiently from cache and may not be materially affected by
memory bandwidth. Memory configuration is a balance between memory bandwidth and future
capacity growth. It is advisable to match the number of memory options to the number of
CPUs. (Case B)
- Data mining can benefit from additional memory bandwidth. In these cases, configure four
memory options, two per CPU. (Case A)
- The most demanding high-performance technical applications (HPTC) achieve a performance
level that is directly proportional to memory bandwidth. In these cases, configure four
memory options, two per CPU. (Case A)
|
|
512-MB RDRAM Memory (4x128)
Option |
3X-MS7AB-AA |
|
512-MB RDRAM Memory (1x128)
RAID Option |
3X-MS7AB-AC |
|
1-GB RDRAM Memory (4x256)
Option |
3X-MS7AB-BA |
|
1-GB RDRAM Memory (1x256) RAID
Option |
3X-MS7AB-BC |
|
2-GB RDRAM Memory (4x512)
Option |
3X-MS7AB-CA |
|
2-GB RDRAM Memory (1x512) RAID
Option |
3X-MS7AB-CC |
| |
| Step 5 - System Disk - Mandatory |
- Mandatory selection of at least one system disk drive
is required for each ES47 Tower system ordered. NOTE: Integrated Ultra3 SCSI controller for internal disk drives
and cabling included.
- ES47 Tower systems support up to two internal hard disk
drives.
|
|
36.4-GB Ultra320 SCSI 10,000 rpm
1-inch Universal disk drive |
3R-A3838-AA |
|
72.8-GB Ultra320 SCSI 10,000 rpm
1-inch Universal disk drive |
3R-A3839-AA |
|
146-GB Ultra320 SCSI 10,000 rpm
1-inch Universal disk drive |
3R-A3841-AA |
|
18.2-GB Ultra320 SCSI 15,000 rpm
1-inch Universal disk drive |
3R-A3848-AA |
|
36.4-GB Ultra320 SCSI 15,000 rpm
1-inch Universal disk drive |
3R-A3849-AA |
|
72.8-GB Ultra320 SCSI 15,000 rpm
1-inch Universal disk drive |
3R-A3851-AA |
| |
| Step 6 - Tower Enclosure Power Cords - Mandatory |
- Mandatory
selection of two power cords required for each ES47 Tower system
ordered
NOTE: Power supplies included
with the Base System
|
|
North American, |
BN26J-1K |
|
Australia, New Zealand, 2.5-meter |
BN19H-2E |
|
Central Europe, 2.5-meter |
BN19C-2E |
|
Denmark, 2.5-meter |
BN19K-2E |
|
Egypt, India, South Africa,
2.5-meter |
BN19S-2E |
|
Israel, 2.5-meter |
BN18L-2E |
|
Italy, 2.5-meter |
BN35M-02 |
|
Japan, 2.5-meter, Dentori
approved |
3X-BN46F-02 |
|
Switzerland, 2.5-meter |
BN19E-2E |
|
UK, Ireland, 2.5-meter |
BN19A-2E |
|
|
|
| I/O Configuration Guidelines: |
| ES47 Tower systems
support six total slots spread over three buses (ports). The following table details the
internal I/O slots: |
| Port # |
Slot # |
Maximum Bus Speed |
Signal Voltage |
Number of Devices Supported |
| 0 |
1 |
133 MHz |
3.3 V |
1 133 MHz or 66 MHz PCI-X
or
1 66 or 33 MHz PCI |
| 1 |
1 |
66 MHz |
3.3 V |
2 66 MHz PCI-X
or
2 66 MHz PCI or
4 33 MHz PCI |
| 2 |
66 MHz |
3.3 V |
| 3 |
66 MHz |
3.3 V |
| 4 |
66 MHz |
3.3 V |
| 3 |
1 |
2X AGP |
1.5 V |
1 1X or 2X AGP |
| Step 7a
Storage Adapters/Controllers |
| |
Maximum
# Supported |
|
| Tru64 UNIX |
OpenVMS |
| |
Per System |
Per System |
Speed |
PCI/PCI-X Slot |
|
| SCSI |
|
|
|
|
|
| PCI 2-port Ultra3 (LVD) SCSI
adapter, 64-bit/66-MHz dual-channel (uses one PCI slot); includes internal 68-pin and
external 68-pin VHDCI connectors; requires 3X-BC56J-xx cable to connect adapter to
DS-SL13R-Bx shelf; HSZxx RAID controllers not supported. No shared SCSI or tape support,
no SDLT tape support. No support for Model 4314R single-bus shelves with 3X-KZPEA-DB
adapter. Tru64 UNIX requires graphics adapter to run console utilities (RUN BIOS). |
4 |
4 |
66 MHz |
3.3V PCI |
3X-KZPEA-DB |
Ultra160 cable, VHDCI to VHDCI
(341174-B21 6-feet, 341175-B21 12-feet, 164604-B21 24-feet)
xx = 02 (6-feet), 03 (12-feet), 04 (24-feet) |
|
3X-BC56J-xx |
| |
|
|
|
|
|
| PCI 1-port UltraSCSI wide
differential 32-bit/33-MHz PCI adapter (uses one PCI slot); includes external 68-pin HD
connector, requires BN38C-xx cable (2 to 25 meters) to connect adapter to differential
UltraSCSI shelf or RAID controller |
4 |
4 |
33 MHz |
3.3V PCI |
3X-KZPBA-CC |
68-pin HD male-to-VHDCI male
UltraSCSI cable;
xx = 02, 03, 05, 10, 20 meters |
|
BN38C-xx |
| |
| RAID |
Ultra160 2-channel internal RAID
controller with 128-MB cache
NOTE: One controller supported
per bus segment; supported only as a data device. |
- |
1 |
66 MHz |
3.3V PCI |
3X-KZPDC-BE |
Ultra160 4-channel internal RAID
controller with 256-MB cache
NOTE: One controller supported
per bus segment; supported only as a data device. |
- |
1 |
66 MHz |
3.3VPCI |
3X-KZPDC-DF |
Ultra160 cable, VHDCI to VHDCI
(341174-B21 6-feet,
341175-B21 12-feet, 164604-B21 24-feet)
xx = 02 (6-feet), 03 (12-feet), 04 (24-feet) |
|
3X-BC56J-XX |
| |
| Fibre Channel |
| PCI to 2-Gbit Fibre Channel
adapter, 64-bit/66-MHz, single-channel |
4 |
4 |
66 MHz |
3.3V PCI |
DS-KGPSA-DA |
Fibre Channel cable
xx=02, 03, 05, 10, 15, 30, 50 meters |
|
BNGBX-xx |
| |
| Step
7b - Storage Expansion Optional |
| StorageWorks
Model 4314T Standalone Enclosures for Universal Drives |
Model 4314T Ultra3
SCSI, single-bus tower enclosure, US |
DS-SL13T-AA |
| Model 4314T Ultra3
SCSI, single-bus tower enclosure, International |
DS-SL13T-AB |
| Model 4314T Ultra3
SCSI, single-bus tower enclosure, Japan |
DS-SL13T-AJ |
| NOTE:
DS-SL13T enclosures include one 12-foot VHDCI to VHDCI SCSI cable |
| Universal Disk
Drives (Supported in Model 4314T Standalone Enclosures) |
|
36.4-GB Ultra320 SCSI
10,000 rpm 1-inch Universal disk drive |
3R-A3838-AA |
|
72.8-GB Ultra320 SCSI 10,000 rpm
1-inch Universal disk drive |
3R-A3839-AA |
|
146-GB Ultra320 SCSI 10,000 rpm
1-inch Universal disk drive |
3R-A3841-AA |
|
18.2-GB Ultra320 SCSI 15,000 rpm
1-inch Universal disk drive |
3R-A3848-AA |
|
36.4-GB Ultra320 SCSI 15,000 rpm
1-inch Universal disk drive |
3R-A3849-AA |
| |
| External Tape
Storage |
| AIT Tabletop Tape
Drives |
AIT 35/70-GB 8-mm LVD tabletop
tape drive, carbon black, North America; requires LVD adapter |
216885-001 |
| Same as above, International |
216885-B31 |
| Same as above, Japan |
216885-291 |
| AIT 50/100-GB 8-mm SCSI tabletop
tape drive with 120V North American power cord, carbon black; requires Ultra2 (LVD)
adapter |
157767-002 |
| Same as above, International |
157767-B32 |
| Same as above, Japan |
157767-292 |
| |
| AIT Hot-plug Tape
Drives (for use in StorageWorks Model 4314T Standalone Enclosures) |
- AIT hot-plug tape drives require two Universal slots
|
|
| AIT 35/70-GB hot-plug LVD
Universal tape drive, uses two slots in 43xxx shelves |
3R-A2396-AA |
| AIT 50/100-GB hot-plug LVD
Universal tape drive, uses two slots in 43xxx shelves |
3R-A2779-AA |
| |
| AIT Autoloaders |
AIT 35-GB tabletop autoloader, 8
cartridge, U.S. |
292355-001 |
| Same as above, International |
292355-B31 |
| |
| AIT Tape Libraries |
SSL2020 AIT tabletop library with
one AIT 50-GB drive and 20 slots, LVD |
175195-B21 |
| SSL2020 AIT tabletop library with
two AIT 50-GB drives and 20 slots, LVD |
175195-B22 |
| |
| DAT Tabletop Tape
Drives |
DAT 12/24-GB 4-mm narrow
single-ended tabletop SCSI tape, includes 120V North American power cord, requires
BN31W-xx SCSI cable |
DS-TLZ10-DB |
| DAT 20/40-GB 4-mm Wide Ultra2
(LVD) tabletop SCSI tape drive with 120V North American power cord, carbon black; requires
Ultra2 (LVD) adapter |
157770-002 |
| Same as above, International |
157770-B32 |
| Same as above, Japan |
157770-292 |
| |
| DAT Hot-plug Tape Drive (for
use in StorageWorks Model 4314T Standalone Enclosures) |
DAT 20/40-GB DDS4 hot-plug LVD
Universal tape drive, uses two slots in 43xxx shelves |
3R-A2780-AA |
| |
| DAT Autoloaders |
DAT 20/40-GB auto loader
external; requires BN31W-xx SCSI cable and 3X-KZPCA-AA, or 3X-DEPVZ-AA adapter, North
America |
166505-001 |
| Same as above, International |
166505-B31 |
| Same as above, Japan |
166505-291 |
| |
| DLT/SDLT Tabletop
Tape Drives |
DLT8000 tabletop 40/80-GB DLT
external tape drive, carbon black - requires
3X-KZPCA-AA LVD adapter - U.S. |
146197-B23 |
| Same as above Japan |
146197-292 |
| SDLT tabletop 110/220-GB external
tape drive, carbon black- requires 3X-KZPCA-AA LVD adapter - U.S. |
192103-002 |
| Same as above
International |
192103-B32 |
| Same as above Japan |
192103-292 |
| SDLT tabletop 160/320-GB external
tape drive, carbon black - requires 3X-KZPCA-AA LVD adapter - U.S. |
257319-001 |
| Same as above -
International |
257319-B31 |
| Same as above -
Japan |
257319-291 |
| |
| DLT/SDLT Tape
Libraries |
MSL5026DLX, DLT tabletop library
with one 40/80-GB DLT tape drive, LVD |
231821-B21 |
| MSL5026DLX, DLT tabletop library
with two 40/80-GB DLT tape drives, LVD |
231821-B22 |
| MSL5026SL, SDLT tabletop library
with one 110/220-GB SDLT tape drive, LVD; graphite |
302511-B21 |
| MSL5026SL, SDLT tabletop library
with two 110/220-GB SDLT tape drives, LVD; graphite |
302511-B22 |
| MSL5026S2, SDLT tabletop library
with one 160/320-GB SDLT tape drive, LVD; graphite |
293473-B21 |
| MSL5026S2, SDLT tabletop library
with two 160/320-GB SDLT tape drives, LVD; graphite |
293473-B21 |
| MSL5000 SDLT2 upgrade drive, all |
293475-B21 |
| MSL5052SL SDLT 110/220-GB drive
field upgrade, LVD |
231823-B22 |
| MSL5052S2, SDLT tabletop library
with two 160/320-GB SDLT tape drives, LVD; graphite |
293476-B21 |
| |
|
|
| Step
8a - Networks and Communications Mandatory |
- Mandatory
selection of at least one of the following Ethernet adapters is required
for each ES47 Tower system ordered
|
| |
Maximum
# Supported |
|
| |
Tru64
UNIX |
OpenVMS |
|
| |
Per System |
Per System |
Speed |
PCI/
PCI-X Slot |
|
| Ethernet Adapters |
PCI (32/64-bit, 33-MHz to 66-MHz)
dual-port 10/100 Ethernet (UTP/RJ45s) NIC and Base Module. (One 3X-DE602-TA or 3X-DE602-FA
optional add-on daughter card can be combined with this module.)
NOTE: Use BN25G, BN26M, BN24Q, or BN28Q
twisted pair RJ45 cables. |
4 |
4 |
66 MHz |
3.3/5 V |
3X-DE602-BB |
PCI-X/PCI Single-port 10/100/1000
Mbps (Twisted-pair Copper with RJ45) Gigabit Ethernet NIC.
Use BN25G, BN26M, BN24Q, BN28Q cables or equivalent w/RJ45 connectors.
NOTE: Only supported in PCI mode.
Supported as a cluster interconnect under OpenVMS only. OpenVMS remedial kit required:
EV7 Tima: DEC-AXPVMSVMS731_EV7-V0100- -4.PCSI
LAN Tima: DEC-AXPVMS-VMS731_LAN-V0100- -4.PCSI |
4 |
4 |
66 MHz |
3.3 V |
3X-DEGXA-TA |
| |
| Step 8b - Networks and Communications Optional |
| Ethernet Adapters |
Dual-port 10/100 Ethernet
(UTP/RJ45) add-on daughter card for use with the 3X-DE602-BB only. The combined
3X-DE602-BB and 3X-DE602-TA modules provide four 10/100 (UTP/RJ45s) ports in a single PCI
slot option
NOTE: 3X-DE602-TA cannot be used
standalone.
Use BN25G, BN26M, BN24Q, or BN28Q twisted pair RJ45
cables. |
4 |
4 |
33 MHz |
3.3/5 V |
3X-DE602-TA |
Single-port 100 Mbps (MMF/duplex-SC)
add-on daughter card for use with the 3X-DE602-BB. The combined 3X-DE602-BB and
3X-DE602-FA provides two 10/100 (UTP/RJ45s) and one 100Mbps (MMF/SC) ports in a
single PCI slot option.
NOTE: 3X-DE602-FA cannot be used
standalone.
Use BN34A or BN34B cables. |
4 |
4 |
33 MHz |
3.3/5 V |
3X-DE602-FA |
PCI-X/PCI Single-port 1000 Mbps
(Fiber with duplex-SC) Gigabit Ethernet NIC.
Use BN34A, BN34B cables or equivalent with SC connectors.
NOTE: Only supported in PCI mode.
Supported as a cluster interconnect under OpenVMS only. OpenVMS remedial kit required:
EV7 Tima: DEC-AXPVMSVMS731_EV7-V0100- -4.PCSI
LAN Tima: DEC-AXPVMS-VMS731_LAN-V0100- -4.PCSI |
4 |
4 |
66 MHz |
3.3 V |
3X-DEGXA-SA |
| |
| FDDI Controllers |
PCI (32-bit, 33-MHz) to FDDI SAS
(MMF/duplex-SC) NIC
Use BN34A, BN34B, or BN34D cables. |
4 |
4 |
33 MHz |
3.3/5 V |
3X-DEFPA-AC |
PCI (32- bit, 33-MHz) to FDDI DAS
(MMF/duplex-SC) NIC
Use BN34A, BN34B, or BN34D cables. |
4 |
4 |
33 MHz |
3.3/5 V |
3X-DEFPA-DC |
PCI (32-bit, 33-MHz) to FDDI DAS
(UTP/RJ45) NIC
Use BN25G, BN26M, BN24Q, or BN28Q twisted pair RJ45 cables. |
4 |
4 |
33 MHz |
3.3/5 V |
3X-DEFPA-MC |
PCI (32-bit, 33-MHz) to FDDI SAS
(UTP/RJ45) NIC
Use BN25G, BN26M, BN24Q, or BN28Q twisted pair RJ45 cables. |
4 |
4 |
33 MHz |
3.3/5 V |
3X-DEFPA-UC |
Multimode fiber optic (MMF)
62.5/125um duplex cable with SC-to-MIC connectors
xx = available lengths: (01, 03, and 10) for 1, 3, and 10 meters |
|
BN34D-xx |
| Synchronous/Asynchronous
Controllers |
| PCI (32-bit, 33-MHz) to Dual-port
Intelligent Synchronous Communications NIC -- Requires at least one (maximum two) BN34x
sync cable listed below |
- |
2 |
33 MHz |
3.3/5 V |
3X-PBXDD-AA |
| PCI (32-bit, 33-MHz) to Quad-port
Intelligent Synchronous Communications NIC -- Requires at least one (maximum four) BN34x
sync cable listed below. |
- |
2 |
33 MHz |
3.3/5 V |
3X-PBXDD-AB |
| Synchronous-specific Cables |
| EIA-530 single-port cable |
|
3X-BC34G-06 |
| V.24/EIA-232 single-port cable |
|
3X-BC34L-06 |
| V.11/x.21 single-port cable |
|
3X-BC33S-06 |
| V.35 single-port cable |
|
3X-BC34T-06 |
| |
| ATM Adapters |
PCI (32-bit, 33-MHz) to 155 Mbps
ATM, Copper NIC with RJ45 connector
Use BN25G-xx, or BN26M-xx cables. |
4 |
4 |
33 MHz |
3.3/5 V |
3X-DAPBA-UA |
PCI (32-bit, 33-MHz) to 155 Mbps
ATM Fiber NIC with SC connector
Use BN34B-xx cable. |
4 |
4 |
33 MHz |
3.3/5 V |
3X-DAPBA-FA |
| |
| Asynchronous Communications |
| PCI (32-bit, 33-MHz) to 4-port
Async Communications NIC with DB-25 octopus cable. |
2 |
2 |
33 MHz |
3.3/5 V |
PBXDA-BA |
| PCI (32-bit, 33-MHz) to 16-port
Async Communications Controller and rackmount 16-port distribution box with RJ45
connectors |
2 |
2 |
33 MHz |
3.3/5 V |
PBXDA-AC |
| Asynchronous Connector
Adapters |
| RJ45-to-DB-25 Converter Cable |
|
CXI01-AC |
| RJ45-to-DEC MJ11 Converter Cable
(8 pack) |
|
CXI01-AF |
| Ethernet, FDDI, ATM Cables |
| Multimode fiber optic (MMF)
62.5/125um duplex cable, with SC-to-ST connectors. xx = available lengths: (2E, 4E, 01,
03, 10, 20, 30) for 2.4, 4.5, 1, 3, 10, 20, and 30 meters |
|
BN34A-xx |
| Multimode fiber optic (MMF)
62.5/125um duplex cable, with SC-to-SC connectors. xx = available lengths: (2E, 4E, 01,
03, 10, 20, 30) for 2.4, 4.5, 1, 3, 10, 20, and 30 meters |
|
BN34B-xx |
| Category 5e (4-Unshielded Twisted
Pairs / UTP) straight-through cable with RJ45-to-RJ45 connectors for system to switch,
repeater, or hub connectivity. xx = available lengths: (0B, 0E, 01, 03, 04, 07) for 0.2,
0.5, 1, 3, 4, and 7 meters |
|
BN25G-xx |
| Category 5e (4-Twisted Pairs,
Screened/ ScTP) straight-through cable with RJ45-to-RJ45 connectors for system to switch,
repeater, or hub connectivity. xx = available lengths: (0E, 01, 03, 04, 07) for 0.5, 1, 3,
4, and 7 meters |
|
BN26M-xx |
Category 5e (4-Unshielded Twisted
Pairs / UTP) Xover cable with RJ45-to-RJ45 connectors for system to switch, repeater, or
hub connectivity.
xx = available lengths: (0E, 01, 03, 04, 07) for 0.5, 1, 3, 4, and 7 meters |
|
BN24Q-xx |
Category 5e (4-Twisted Pairs,
Screened / ScTP) Xover cable with RJ45-to-RJ45 connectors for system to switch, repeater,
or hub connectivity.
xx = available lengths: (0E, 01, 03, 04, 07) for 0.5, 1, 3, 4, and 7 meters |
|
BN28Q-xx |
| |
| Step 9 -
Graphics Optional |
- Select graphics adapter, monitor, and country-specific keyboard for Tru64 UNIX and
OpenVMS systems if required
|
| |
Maximum
# Supported |
|
| |
Tru64 UNIX |
OpenVMS |
| |
Per System |
Per System |
Speed |
PCI/
AGP Slot |
|
| 3Dlabs Oxygen VX1 32-MB PCI 2D
graphics accelerator |
1 |
1 |
66 MHz |
3.3V PCI |
SN-PBXGF-AB |
| 3Dlabs Oxygen VX1 32-MB AGP 2D
graphics accelerator |
1 |
1 |
4X(1) |
AGP |
SN-PBXGF-BC |
| ATI Radeon 7500 2D AGP graphics
accelerator |
1 |
- |
4X(1) |
AGP |
3X-PBXGG-AB |
| (1) Only supported in 2X mode |
| Maximum graphics adapters per systems, all
types - Tru64 UNIX: 2 (1 AGP and 1 PCI or 2 PCI), OpenVMS: 2 (1 AGP and 1 PCI or 2 PCI) |
| |
| Step 10 - Mouse, Monitors, and Keyboards |
| Mouse |
3-button mouse - USB |
3X-PBQWS-WB |
|
|
|
| PS2 to USB Converter |
Keyboard and Mouse adapter for
USB - allows for connection of a PS2 keyboard and/or mouse to an AlphaServer ES47 Tower
System |
3R-A4495-AA |
| |
|
| Monitors |
- Graphics monitors other than those listed can be used if compatible with SVGA graphics
ordered with system
- A video cable, 6-foot/1.8-meter length, is included with all variants of monitors
- Video extension cable required if monitor is located more than 1-meter from server
- Monitors will ship with, but not be integrated with systems.
|
| |
| Carbon/Silver Monitors |
V7550 17-inch (16-inch viewable
image size) flat-faced shadow mask color monitor, two-tone (carbon/silver), 0.25mm dot
pitch, VGA to 1024 x 768 @85 Hz, MPRII/TCO99/
Energy Star compliant, Northern Hemisphere with NA power cord, VGA cable |
3R-A4002-AA |
|
Same as above, with Euro power
cord |
3R-A4201-AA |
|
Same as above, APD, no power cord |
3R-A4202-AA |
|
Same as above, with PRC power
cord, CCIB |
3R-A4446-AA |
|
Same as above, Southern
Hemisphere, with Australia/New Zealand power cord |
3R-A4203-AA |
| |
|
|
|
P930 19-inch (18-inch
viewable image size) auto-scanning color monitor, Diamondtron NF, 0.24-mm aperture grille
pitch, VGA to 1600 x 1200 @85 Hz, MPRII/TCO 99/Energy Star Compliant, Northern Hemisphere
with NA power cord, VGA cable |
3R-A4215-AA
|
|
Same as above, with
Euro power cord |
3R-A4391-AA |
|
Same as above,
Taiwan, with NA power cord |
3R-A4392-AA |
|
Same as above, with
PRC power cord, CCIB |
3R-A4394-AA |
|
Same as above,
Southern Hemisphere, 0.25 to 0.27 mm aperture grille pitch, with Australia/New Zealand
power cord |
3R-A4393-AA
|
| |
|
|
|
P1130 21-inch
(19.8-inch viewable image size) FD Trinitron auto-scanning color monitor, 0.24-mm aperture
grille pitch, VGA to 1792 x 1344 @85Hz, dual video input, USB Hub, MPRII/TCO 99/Energy
Star Compliant, Northern Hemisphere with NA power cord, VGA cable |
3R-A4216-AA
|
|
Same as above, with
Euro power cord |
3R-A4396-AA |
|
Same as above,
Taiwan, no power cord |
3R-A4397-AA |
|
Same as above, with
PRC power cord, CCIB |
3R-A4400-AA |
|
Same as above,
Southern Hemisphere, with Australia/New Zealand power cord |
3R-A4398-AA |
| |
|
|
| Carbon/Silver Flat Panel
Monitors |
TFT1825, 18-inch (18-inch
viewable image size) TFT flat panel monitor, 0.28mm pixel pitch, 1600 x 1200 @60Hz,
multi-mode support, MPRII/TCO99/Energy Star compliant, one VGA, one DVI-I input connector.
NA power cord, VGA and DVI-I cables |
3R-A4292-AA |
|
TFT1520, 15-inch (15-inch
viewable image size) TFT flat panel monitor, 0.297 mm pixel pitch, 1024 x 768 @75 Hz,
multi-mode support, MPRII/TCO99/Energy Star compliant, two video input connectors (one VGA
and one DVI-I), NA power cord, VGA and DVI-I cables |
3R-A4249-AA |
|
|
|
| Monitor Power
Cords |
North American, 120V,
75-inch |
BN26J-1K |
|
Australia, New
Zealand, 2.5-meter |
BN19H-2E |
|
Central Europe,
2.5-meter |
BN19C-2E |
|
Denmark, 2.5-meter |
BN19K-2E |
|
Egypt, India, South
Africa, 2.5-meter |
BN18L-2E |
|
Israel, 2.5-meter |
BN19A-2E |
|
Italy, 2.5-meter |
BN35M-02 |
|
Japan, 2.5-meter,
Dentori approved |
3X-BN46F-02 |
|
Switzerland,
2.5-meter |
BN19E-2E |
|
UK, Ireland,
2.5-meter |
BN19S-2E |
| |
| Keyboards |
| USB Keyboard/Language |
Tru64 UNIX
USB only |
OpenVMS
USB and PS/2 |
| U.S./English keyboard |
3R-LKQ50-AA |
3X-LK463-A2 |
| Arabic keyboard |
3R-LKQ50-BR |
- |
| Belgian keyboard |
3R-LKQ50-AB |
3X-LK463-AB |
| BHCSY keyboard |
3R-LKQ50-AX |
- |
| Canadian/English keyboard |
- |
3X-LK463-AQ |
| Canadian/French keyboard |
3R-LKQ50-AC |
3X-LK463-AC |
| Cyrillic keyboard (Russian) |
3R-LKQ50-BT |
3X-LK463-BT |
| Czech keyboard |
3R-LKQ50-BV |
3X-LK463-BV |
| Danish keyboard |
3R-LKQ50-AD |
3X-LK463-AD |
| Dutch keyboard |
3R-LKQ50-AH |
3X-LK463-AH |
| Finnish keyboard |
- |
3X-LK463-AF |
| French keyboard |
3R-LKQ50-AP |
3X-LK463-AP |
| German keyboard |
3R-LKQ50-AG |
3X-LK463-AG |
| Greek keyboard |
3R-LKQ50-BH |
3X-LK463-BH |
| Hebrew keyboard |
3R-LKQ50-AT |
3X-LK463-AT |
| Hungarian keyboard |
3R-LKQ50-BQ |
3X-LK463-BQ |
| International keyboard |
3R-LKQ50-BA |
- |
| Italian keyboard |
3R-LKQ50-AI |
3X-LK463-AI |
| Japanese keyboard |
3R-LKQ50-AJ |
- |
| Korean keyboard |
3R-LKQ50-BK |
- |
| Latin-American keyboard |
3R-LKQ50-AR |
- |
| Norwegian keyboard |
3R-LKQ50-AN |
3X-LK463-AN |
| Polish keyboard |
3R-LKQ50-BP |
3X-LK463-BP |
| Portuguese keyboard |
3R-LKQ50-AV |
3X-LK463-AV |
| Romanian keyboard |
- |
3X-LK463-BL |
| Simplified Chinese keyboard |
3R-LKQ50-CV |
- |
| Spanish keyboard |
3R-LKQ50-AS |
3X-LK463-AS |
| Swedish keyboard |
3R-LKQ50-AM |
3X-LK463-AM |
| Swiss/French keyboard |
3R-LKQ50-AK |
3X-LK463-AK |
| Swiss/German keyboard |
- |
3X-LK463-AL |
| Traditional Chinese keyboard |
3R-LKQ50-BI |
- |
| Thai keyboard |
3R-LKQ50-CB |
- |
| Turkish keyboard |
3R-LKQ50-BU |
3X-LK463-BU |
| Turkish/F keyboard |
- |
3X-LK463-BW |
| UK keyboard |
3R-LKQ50-AE |
- |
| Yugoslavian keyboard |
- |
3X-LK463-BY |
| |
| Step
11 - System Software |
| Tru64 UNIX |
- Media and documentation required for first system on site
|
|
|
- Software Processor Code = E
|
|
|
- Tru64 UNIX base systems include pre-installed software, Base
license, Unlimited User license, Server Extension license, Internet Express, and Secure
Web Server
|
|
|
Tru64 UNIX media and
online documentation on CD-ROM |
QA-6ADAA-H8 |
| Tru64 UNIX full hard
copy documentation |
QA-6ADAA-GZ |
| TruCluster Plus
Software Package with licenses for TruCluster Server, Logical Storage Manager and AdvFS
Utilities |
QP-6R9AC-AA |
| TruCluster Server
license |
QL-6BRAC-AA |
| Logical Storage
Manager license |
QL-2GVAE-AA |
| AdvFS Utilities
license |
QL-0EGAE-AA |
| Advanced Server for
Tru64 UNIX, 25 client concurrent use license |
QL-5U29M-3D |
| Advanced Server for
Tru64 UNIX, 50 client concurrent use license |
QL-5U29M-3E |
| Advanced Server for
Tru64 UNIX, 100 client concurrent use license |
QL-5U29M-3F |
| Advanced Server for
Tru64 UNIX, 250 client concurrent use license |
QL-5U29M-3G |
| Advanced Server for
Tru64 UNIX, 500 client concurrent use license |
QL-5U29M-3H |
| Layered products
media and documentation for Tru64 UNIX on CD-ROM |
QA-054AA-H8 |
| DECnet/OSI end-system
function license for Tru64 UNIX |
QL-MTJAE-AA |
| DECnet/OSI extended
license for Tru64 UNIX |
QL-MTKAE-AA |
|